| |
| Aluminum Plain & Stucco Embossed Coil |
| |
|
 |
| Quest can supply high quality plain coil for general engineering and for special applications. Prism can produce plain coils form Hot mill route as well as concast route as well as concast route. The coils are supplied in Mill finish. Stucco Embossed coils can also be supplied. |
|
| |
| Aluminum Coil Range |
| Alloy |
Temper |
Thickness (mm) |
Width (mm) |
| 1050/1060/1070 |
H1/H2/H3/H4/O |
0.40 - 5.0 |
500-1500 |
| 1100/1200/8011 |
H1/H2/H3/H4/O |
0.40 - 5.0 |
500-1500 |
| 3003/3105/3005 |
H1/H2/H3/H4 |
0.40 - 5.0 |
500-1500 |
| 5005/5052/5086/5754 |
H1/H2/H3/H4 |
0.40 - 5.0 |
500-1500 |
|
| |
| COIL I.D (MM) |
THICKNESS |
| 200 |
0.18 TO 0.40 |
| 300
|
0.40 TO 0.90 |
| 400/500 |
0.90 TO 4.00 |
|
| |
| Width Tolerance |
Coil Density |
| ± 2 mm |
Max. 3 kgs/ mm width (Hr route) |
| Max. 5.25 kgs/mm width (Caster route) |
|
| |
Chemical Composition % |
| Alloy |
Si |
Fe |
Cu |
Min |
Mg |
Cr |
Zn |
Ti |
Al |
| 1050 |
0.25 max. |
0.40 max. |
0.05 max. |
0.05 max. |
0.05 max. |
- |
0.05 max. |
0.03 max. |
99.50 min. |
| 1060 |
0.25 max. |
0.35 max. |
0.05 max. |
0.03 max. |
0.03 max. |
- |
0.05 max. |
0.03 max. |
99.60 min. |
| 1070 |
0.20 max. |
0.25 max. |
0.04 max. |
0.03 max. |
0.03 max. |
- |
0.04 max. |
0.03 max. |
99.70 min |
| 1100 |
0.95 max. |
0.95 max. |
0.05 max. |
0.05 max. |
- |
- |
0.10 max. |
- |
99.00 min. |
| 1200 |
1.00 max. |
1.00 max. |
0.05 max. |
0.05 max. |
- |
- |
0.10 max. |
0.05 max. |
99.00 Min. |
| 3003 |
0.6 max. |
0.7 max. |
0.05-0.20 |
1.0-1.5 |
- |
- |
0.10 max. |
- |
Rem. |
| 3005 |
0.6 max. |
0.7 max. |
0.30 max. |
1.0-1.5 |
0.2-0.6 |
0.10 max. |
0.25 max. |
0.10 max. |
Rem. |
| 3105 |
0.6 max. |
0.7 max. |
0.30 max. |
0.30-0.8 |
0.20-0.8 |
0.20 max. |
0.40 max. |
0.10 max. |
Rem. |
| 5005 |
0.30 max. |
0.7 max. |
0.20 max. |
0.20 max. |
0.50-1.1
|
0.10 max. |
0.25 max. |
- |
Rem. |
| 5052 |
0.25 max. |
0.40 max. |
0.10 max. |
0.10 max. |
2.2-2.8 |
0.15-0.35 |
0.10 max. |
- |
Rem. |
| 5086 |
0.40 max. |
0.50 max. |
0.10 max. |
0.2-0.7 |
3.5-4.50 |
0.05-0.25 |
0.25 max. |
0.15 max. |
Rem. |
| 8011 |
0.50-0.9 |
0.6-1.0 |
0.10 max. |
0.20 max. |
0.05 max. |
0.05 max. |
0.10 max. |
0.08 max. |
Rem. |
|
| |
Thickness Tolerance |
| Specified Thickness (mm) |
Tolerance (± mm) |
| Over |
Thru |
Upto |
Over |
| 1000mm Width |
1000 mm Wdth |
| 0.18 |
0.25 |
0.35 |
0.06 |
| 0.25 |
0.4 |
0.04 |
0.07 |
| 0.4 |
0.63 |
0.05 |
0.08 |
| 0.63 |
0.8 |
0.06 |
0.09 |
| 0.8 |
1 |
0.07 |
0.1 |
| 1 |
1.2 |
0.08 |
0.11 |
| 1.2 |
1.6 |
0.08 |
0.12 |
| 1.6 |
2 |
0.09 |
0.14 |
| 2 |
2.5 |
0.1 |
0.16 |
| 2.5 |
3.2 |
0.12 |
0.18 |
| 3.2 |
4 |
0.14 |
0.22 |
|
| |
| Packaging |
| Belly type with side Disc. (BTSD) |
| Eye to Sky Packing (2. M.T. Max.) |
| |
| Circles in specification other than those mentioned can also be supplied subject to confirmation. |
| |
| NOTE: Aluminum Plain Coils & Stucco Embossed Coils can be supplied in half of the Thickness Tolerances mentioned in the table against specific requirements.
Coils in specification other than those mentioned can also be supplied subject to confirmation. |
| |
| Back |
Top |
| |
