| |
 |
| |
Flooring Sheets in specification other than those mentioned can also be supplied subject to confirmation.
|
|
| |
| Aluminum Flooring Sheet (5 Bar, Diamond and Two Bar) |
| |
| Alloy |
Temper |
Thickness (mm) |
Width (mm) |
Length (mm) |
| 1100/1050/1060 |
H4/T4/T6 |
2.0 - 4.0 |
813 /914/1220 |
1000-5500 |
| 3003 |
H4/T4/T6 |
2.0 - 4.0 |
813 /914/1220 |
1000-5500 |
| 5052 |
H4/T4/T6 |
2.0 - 4.0 |
813 /914/1220 |
1000-5500 |
| 6061 |
F/M/T4/T6 |
2.0 - 4.0 |
813 /914/1220 |
1000-5500 |
| 8011 |
H4/T4/T6 |
2.0 - 4.0 |
813 /914/1220 |
1000-5500 |
|
| |
| Aluminum Paneling Sheet (5 Bar, Diamond and Two Bar) |
| |
| Alloy |
Temper |
Thickness (mm) |
Width (mm) |
Length (mm) |
| 1100/1050/1060 |
H2 |
0.60 - 1.20 |
813 /914/1220 |
1000-5500 |
| 8011 |
H2 |
0.60 - 1.20 |
813 /914/1220 |
1000-5500 |
|
| |
Chemical Composition % |
| Alloy |
Si |
Fe |
Cu |
Min |
Mg |
Cr |
Zn |
Ti |
Al |
| 5052 |
0.25 max. |
0.40 max. |
0.10 max. |
0.10 max. |
2.2-2.8 |
0.15-0.35 |
0.10 max. |
- |
Rem. |
| 6061 |
0.4-0.8 |
0.7 max. |
0.15-0.40 |
0.15 max. |
0.8-1.2 |
0.4-0.35 |
0.25 max. |
0.15 max |
Rem. |
| 6351 |
0.70-1.3 |
0.50 max. |
0.10 max. |
0.40 -0.8 |
0.40-0.8 |
- |
0.20 max. |
0.20 max. |
Rem. |
| 7039 |
0.30 max. |
0.4 max. |
0.10 max. |
0.1-0.40 |
2.3-3.3 |
0.15-0.25 |
3.5-4.5 |
0.10 max. |
Rem. |
|
| |
Thickness Tolerance |
| Specified Thickness (mm) |
Tolerance (± mm) |
| Over |
Thru |
Upto 1000 mm Width |
Over 1000 mm Wdth |
| 1 |
1.2 |
0.08 |
0.11 |
| 1.2 |
1.6 |
0.08 |
0.12 |
| 1.6 |
2 |
0.09 |
0.14 |
| 2 |
2.5 |
0.1 |
0.16 |
| 2.5 |
3.4 |
0.12 |
0.18 |
| 3.2 |
4 |
0.14 |
0.22 |
|
| |
Pattern Height (mm) |
| Base Thickness |
Diamond |
5 Bar/ 2 Bar |
| 1.20-1.60 |
0.35 |
0.4 |
| 1.61-2.00 |
0.4 |
0.45 |
| 2.01-2.49 |
0.55 |
0.6 |
| 2.50 & above |
0.7 |
0.7 |
|
| |
| Packaging |
| Wooden Box / Wooden Pallet with edge protector & Interleaving with poly film. |
| |
| Hot Rolled Plates in specification other than those mentioned can also be supplied subject to confirmation |
| |
| Note: Aluminum Flooring Sheets can be supplied in half of the Thickness Tolerances mentioned in the Table, against specific requirement. |
| |
| Note: We can also offer sheet/coil in non-standard sizes provided our MOQ conditions are met. |
| |
| Back |
Top |
| |
